In a prior article we focused on the key what to be aware of when buying LED Strip Lights for the first time. Now we will take you through another phase; installation. Installing your LED Strips may be anything from very simple to quite difficult, but ultimately it will depend on which outcome you want to achieve with your lighting system. As an example, introducing a 1 metre strip of LED lighting into your kitchen cabinet may be a much more self-explanatory than using 20 metres of RGB LED Strip Lights to outfit a team and run this on DMX Control. Regardless of what you do there are a few universal what to be aware of and this information will take you through a number of them.
We shall focus on the LED Tape itself. This is made up of long little bit of high impact, flexible circuit board with surface mounted devices, or SMDs, positioned along its length. There are a few different what to consider here including, LEDs per metre, LED chip size, strip light colour and length. Strip Lights are available in two LED per metre varieties, 30 LED per metre and 60 LED per metre. As suggested by the name the latter has two times as many LEDs and will be a lot brighter compared to the former. They are designed to be found in a lighting context where they are forced to contend with background illumination. So for instance if you intend to use them in a daylight setting, like a shop street display, or add them to a space that already has general illumination and still want them to be seen, you should opt for 60 LED per metre as their sharper light output makes them suited to these purposes. Irrespective of this a 30 LED per metre strip will be able to handle other lighting arrangements, such as for example club setups, or elsewhere they don’t need certainly to contend with background lighting.
Whenever you consider the specifications of strip lighting you will usually notice some four numbers that to most people might not mean a lot. These actually reference how big is the in-patient LEDs on the strips. Typically you will find chip sizes of either 5050 (5mm by 5mm) or 3528 (3.5mm by 2.8mm). The main element difference between those two types of chip size may be the consistency of light they produce. Smaller LEDs can create a more jagged and inconsistent effect, while larger LEDs provides a more even spread of light.
Another decision to make is exactly what colour strip light you intend to buy. They’re usually available in three main colour varieties, including warm and cool white and interchangeable RGB led strips lights. The former two are for adding stylish ambient lighting to commercial and domestic settings while avoiding being too garish with the end result. They can be used to aesthetically to improve the appearance of a space by the addition of layered or accent lighting, or they can add functionality to kitchens, bathrooms or offices where they can be used as task lighting to assist work. RGB LED is just a direct replacement old fashioned disco lighting and offers a large number of programmable effects. Typically they will run directly from a handy remote control which works along with a red eye sensor attached between the strip light and transformer. However, DMX Control can be an option. This is a kind of advanced effects programming that uses an industry standard signal to manage the brightness, colour and frequency of the lights.
The absolute most obvious consideration to make is the precise amount of strip lighting that you require. This depends upon the type of your setup and how complex your intentions are. Usually most lighting arrangements can be performed with just one strip. Strip Lights are available in 5 metre and 10 metre reels as standard, but longer or shorter bespoke lengths may be ordered so call your provider to get out. Lengthening or shortening strip lighting can be done all by yourself as well. To shorten a reel light can be done by cutting the strip at one of its cutting points spaced approximately 5cm apart along along the light. To attach two items of strip together, and thereby increase along the light, you will require a soldering iron and some two core wire. Simply solder these wires for their respective plus and minus solder points by the end of the strip light where in actuality the cut has been made and do the exact same on one other strip to accomplish the connection. This approach can be used to accomplish a bit of extra length, particularly when trailing them around a big corner.
This article has given you a some of the main specifications associated with LED Strip Lighting and how to make certain you receive exactly the right light you would like for the purposes. Be aware of additional articles on the best way to make sure you meet the energy requirements of your lighting system.